______________________________________________________________________________________ 19
Single-Port, 40W, IEEE 802.3af/802.3at PSE
Controller with Integrated MOSFET
The MAX5971A also contains an internal square wave,
PWM signal generator. The PWM runs at a typical fre-
quency of 25kHz with an approximate typical duty cycle
of 6.25%. PWMEN is used to enable or disable the PWM.
PWMEN is internally pulled up to the digital supply, and
can be left unconnected to enable the internal PWM.
When enabled, the LED pulses are driven by the PWM
to reduce the power dissipation and increase the system
efficiency. Force PWMEN low to disable the internal
PWM; the LED is then driven directly.
Thermal Shutdown
If the MAX5971A die temperature reaches 150NC, an
overtemperature fault is generated and the device shuts
down. The die temperature must cool down below 130NC
to remove the overtemperature fault condition. After a
thermal shutdown condition clears, the device is reset.
Applications Information
Layout Procedure
Careful PCB layout is critical to achieve high efficiency
and low EMI. Follow these layout guidelines for optimal
performance.
1) Place the input bypass capacitance and the output
bypass capacitor (0.1礔 ceramic capacitor from
AGND to OUTP) as close to the MAX5971A as pos-
sible.
2) Use large SMT component pads for power dissipat-
ing devices such as the MAX5971A and the external
diodes in the high-power path.
3) Use short, wide traces whenever possible for high-
power paths.
4) Use the MAX5971 Evaluation Kit as a design and
layout reference.
5) The exposed pad (EP) must be soldered evenly to the
PCB ground plane for proper operation and power
dissipation. Use multiple vias beneath the exposed
pad for maximum heat dissipation. A 1.0mm to
1.2mm pitch is the recommended spacing for these
vias and they should be plated (1oz copper) with a
small barrel diameter (0.30mm to 0.33mm).
Figure 6. Typical Operating Circuit 1 (DC Load Removal Detection, Internal PWM Enabled for LED Indication, and Class 5
Detection Enabled)
1N4448
1kI
1kI
1nF
-54V
5.1kI
LED
10mH
1N4448
0.1礔
100V
47礔
100V
-54V
LED
AGND
EN
V
EE
V
EE_DIG
LEGACY
MIDSPAN
OSC
OUT
OUTP
DET
ILIM1
ILIM2
PWMEN
MAX5971A
0.1礔
100V
SMJ58A
2.2MI
PSE OUTPUT
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX5972AETE+T
IC CONTROLLER INTERFACE 16TQFN
MAX5978ETJ+
IC CTLR HOT-SWAP 32TQFN
MAX5981BETE+
IC CTRLR PD IEEE 802.3AF 16TQFN
MAX5986AETE+
IC POE SWITCH PSE 16TQFN
MAX6509CAZK/V+T
IC TEMP SWITCH RES-PROG 5TSOT
MAX6513TT075+T
IC TEMP SWITCH REMOTE 6-TDFN
MAX6581TG9A+
IC TEMP SENSOR 8-CH PREC 24-TQFN
MAX6602UE9A+T
IC TEMP MONITOR 5CH 16-TSSOP
相关代理商/技术参数
MAX5971AETI+T
功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971AETI+W
制造商:Maxim Integrated Products 功能描述:IEEE802.3 AT PSE SWITCH - Rail/Tube
MAX5971AEVKIT
功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
MAX5971AEVKIT+
制造商:Maxim Integrated Products 功能描述:PD INTERFACE CONTROLLER - Boxed Product (Development Kits)
MAX5971BETI
制造商:Maxim Integrated Products 功能描述:
MAX5971BETI+
功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971BETI+T
功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971BETI+W
制造商:Maxim Integrated Products 功能描述:SINGLE-PORT, 40W, IEEE 802.3AF/AT, PSE CONTROLLER WITH IC - Rail/Tube